Motorised Magstripe/IC Card Encoder

1 General Specifications [1] External dimensions Width 124 +/- 1 mm Height 90 +/- 1 mm Length 210 +/- 1 mm (See Hardware Overview) [2] Weight Approx.1.5kg [3] Card transport method Motor driven [4] Card ejection direction Front and rear directions [5] Card transport speed 200 mm/s +/- 10% or about 300 mm/s selectable by command. 300 mm/s is set as the default speed. Approx.100 mm/s in IC Card handling. [6] Position of installation Upright position can be installed. Up-side-down installation is not supported. [7] Card position detection Photo sensor at 4 places. The state of all sensors can be retrieved by command. [8] Retrieval A card can be retrieved by a command from the host when the card is not pulled out within an interval time. [9] Reject Box (1)Installation The reject box can be mounted at the rear of CHU. The reject box is prepared by customers. (2)Rejected cards number The rejected cards number can be reported by a command from the Host. Notice for General Specification See 21.Appendix C (1) 2 Applicable IC card specifications [1] Number and location of contacts on IC card Number and location of contacts on IC card are specified in ISO 7816-2 figure 2 (See Appendix A). [2] IC card specifications (1) Asynchronous card 1) Support IC cards In Conformity to ISO/IEC7816-1/2/3, EMV4.2 2) Protocol T=0 and/or T=1 (Automatic protocol type selection via ATR detection is possible.) 3) Data byte reading/writing Inverse convention (MSB first, negative logic) and direct convention (LSB first, positive logic) are available. 4) Clock during ATR In conform to ISO / IEC 7816-3 (3.5795MHz) 5) Clock after ATR 3.57MHz or 7.14MHz 6) Communication speed 1etu = (F/D)X1/(3.5795X106) sec The combination of F and D is described in the Appendix B The communication speed can be changed in the setting of PPS procedure. 7) Vcc Both 3V and 5V (Automatic selection via T=15 of ATR detection is possible.) 8) EMV Approval EMV 4.2 Level1 Approved (12259 0409 400 20 TUV) 9) PBOC Approval PBOC2.0 Level1 Approved (TMEF10G041TP) (2) Synchronous card 1) Support IC cards In conform to ISO/IEC7816-1/2/10, SLE4418/4428/4432/4442, AT24C01ASC/AT24C02SC/AT24C16SC/AT24C64SC and I2C 2) Vcc 5V [3] IC Card Handling (1) The contact mechanism is pulled down and IC contacts station is pushed down onto IC card when a card is transported to the proper position. (2) The state of the IC contact echo sensor can be checked by a command from the Host. (3) The resistance between IC contact on card and one on CHU is 500 milliohm or less. Notice for IC Card (ICC) See 21.Appendix C (2) 3 Applicable SAM chip [1] Number and location of SAM Sockets The socket for one SAM is equipped in the main printed circuit board. [2] SAM chip specification 1) Support SAM chips In conformity to ISO/IEC 7810(ID000), ISO/IEC 7816-1/2/3 2) Protocol T=0 and/or T=1 (Automatic protocol type selection via ATR detection is possible.) 3) Data byte reading/writing Inverse convention (MSB first, negative logic) and direct convention (LSB first, positive logic) are available. 4) Clock during ATR In conformity to ISO/IEC 7816-3 (3.5795MHz) 5) Clock after ATR In conformity to ISO/IEC 7816-3 (3.5795MHz) 6) Communication speed 1etu = (F/D)X1/(3.5795X106) sec The combination of F and D is described in the Appendix B The communication speed can be changed in the setting of PPS procedure. 7) VCC Both 3V and 5V (Automatic selection via T=15 of ATR detection is possible.) [3] SAM chip Handling (1) The chip should be set and removed when power is off (2) The SAM socket should be locked stably in operation. (3) The state of the SAM chip can be checked by a command from the Host. Notice for SAM chip See 21.Appendix C (2) 4 Applicable magnetic card [1] Magnetic card type In conform to ISO/IEC 7810/ID-1, 7811-1/2/6 [2] Magnetic card coercivity ISO/IEC 7811-6 LoCo Read/Write default supported [3] Reading function Read specified tracks simultaneously. [4] Writing function Write specified tracks simultaneously. [5] Magnetic recording method Two-Frequency Recording Method (F2F) [6] Magnetic R/W head Structure: Single Gap Head Material : Permalloy + Ceramic Block Width of Tracks 3 mm (Writing) 1 mm (Reading)